View BA6418_104417.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Motor driver ICs
Reversible motor driver
BA6418N
The BA6418N is a reversible-motor driver with a maximum output current of 0.7A. Two logic inputs allow four output modes: forward, reverse, stop (idling), and brake. Since logic and power sections have separate ground pins, the IC can drive speed-variable, reversible motors by connecting an electronic governor circuit. FFeatures 1) Small standby circuit current. 2) Wide range of operating voltage. (4.5 X 15V) FBlock diagram
3) Interfaces with TTL devices. 4) Built-in thermal shutdown circuit.
FAbsolute maximum ratings (Ta = 25_C)
462
Motor driver ICs
FInput / output truth table
BA6418N
FElectrical characteristics (unless otherwise noted, Ta = 25_C, VCC = 9V)
FInput / output circuit (Equivalent circuit)
FApplication example
463
Motor driver ICs
FThermal derating curve
BA6418N
FOperation notes (1) The quality of these products have been carefully checked; however, use of the products with applied voltages, operating temperatures, or other parameters that exceed the absolute maximum rating given may result in the damage of the IC and the product it is used in. If the IC is damaged, the short mode and open modes cannot be specified, so if the IC is to be used in applications where parameters may exceed the absolute maximum ratings, then be sure to incorporate fuses, or other physical safety measures. (2) GND potential The potential for pin 1 must be kept lower than the potensials ofthe other pins regardless of the circumstances. (3) Input pins Voltage should never be applied to the input pins when the VCC voltage is not applied to the IC. Similarly, when VCC is applied, the voltage on each input pin should be less than VCC and within the guaranteed range for the electrical characteristics. (4) Back-rush voltage Depending on the ambient conditions, environment, or motor characteristics, the back-rush voltage may fluctuate. Be sure to confirm that the back-rush voltage will not adversely affect the operation of the IC.
(5) Large current line Large currents are carried by the motor power supply and motor ground for these ICs. Therefore, the layout of the pattern of the PC board and the constants of certain parameters for external components, such as the capacitor between the power supply and ground, may cause this large output current to flow back to the input pins, resulting in output oscillation or other malfunctions. To prevent this, make sure that the PC board layout and external circuit constants cause no problems with the characteristics of these ICs. (6) Power dissipation The power dissipation will fluctuate depending on the mounting conditions of the IC and the ambient environment. Make sure to carefully check the thermal design of the application where these ICs will be used. (7) Power consumption The power consumption by the IC varies widely with the power supply voltage and the output current. Give full consideration to the power dissipation rating and the thermal resistance data and transient thermal resistance data, to provide a thermal design so that none of the ratings for the IC are exceeded. (8) Current consumption The ratio of current consumption (ICC1 versus ICC2) is 1 : 2 for the logic section GND (pins 2 and 5) and the power section GND (pin 8).
464
Motor driver ICs
(9) ASO Make sure that the output current and supply voltage do not exceed the ASO values. (10) Precautions for input mode switching To ensure reliability, it is recommended that the mode switching for the motor pass once through the open mode. (11) In-rush current There are no circuits built into these ICs that prevent inrush currents. Therefore, it is recommended to place a current limiting resistor or other physical countermeasure. (12) Factors regarding the thermal, power supply, and motor conditions If the potential of the output pin sways greatly and goes below the potential of ground, the operation of the IC may malfunction or be adversely affected. In such a case, place a diode between the output and ground, or other measure, to prevent this. (13) Minimum operating voltage applied between power supply (pin 6) and COM (pin 8) The minimum operating voltage applied between these pins is 4V at an ambient temperature of 25_C, but the voltage increases by 8mV (typical) for each degree below 25_C. Keep in mind this negative temperature dependence when setting the voltage at low ambient temperatures. (14) Thermal shutdown circuit When the thermal shutdown circuit is activated at the IC junction temperature of about 175_C (typical), all driver outputs are turned OFF. There is a temperature difference of about 15_C (typical) between the temperatures at which the circuit is activated and deactivated. (15) To eliminate motor noise, connect a capacitor between OUT1 (pin 9) and GND and between OUT2 (pin 7) and GND. Alternatively, connect a capacitor between OUT1 and OUT2, and also a diode between OUT1 and GND and between OUT2 and GND (see Fig. 4).
BA6418N
465
Motor driver ICs
FElectrical characteristic curves
BA6418N
FExternal dimensions (Units: mm)
466

▲Up To Search▲

Price & Availability of BA6418

	To Download BA6418 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .